Nice Run HS RUN1200HS Sliding Gate Kit, up to 1200 kg

Overview

The Nice Run HS kit (RUN1200HS) automates a heavy sliding gate of up to 1200 kg at high speed, so the gate is out of the way sooner at a busy home or industrial entrance. The RUN1200HS is a fast, non-reversible gearmotor with a 24 V DC motor fed from 230 V AC mains, an integrated control unit and an electromechanical limit switch, with accessories connected over Nice BlueBUS. The kit adds a plug-in two-way radio receiver, two remotes and a pair of BlueBUS photocells.

Is it right for you?

• It suits a sliding gate weighing up to 1200 kg at a home or an industrial site; check the gate weight before ordering.
• At 0.37 m/s and 60 cycles per hour it is built for gates that open often and need to move quickly: a 4 m gate opens in about 6 seconds and a 7 m gate in about 18 seconds with a standard installation, excluding acceleration and deceleration.
• The kit has no flashing light, so plan to add one.
• The gearmotor is IP44 rated and works from -20 to 50 °C, so it is made for fitting beside the gate outdoors.

Key features

• Fast 24 V DC motor powered from 230 V AC mains, drawing 2 A and 415 W.
• 790 N of force, moving the gate at 0.37 m/s, rated for 60 cycles per hour.
• Non-reversible gearmotor with an electromechanical limit switch, so the gate stops in the right place at each end of its travel.
• Integrated control unit with accessories connected over Nice BlueBUS on two wires, which keeps the wiring simple.
• OXIBD plug-in bidirectional radio receiver for two-way remotes.
• Two ON2E two-channel 433.92 MHz remotes and an EPMB surface-mounted BlueBUS photocell pair.
• Gearmotor 400 x 255 x 387 mm and 24.5 kg, IP44, -20 to 50 °C.

What else you need

• A rack for the full length of the gate travel; the rack is not included. The gearmotor comes with a module 4 crown for the galvanised ROA7 or ROA8 rack; for the heavier ROA81 module 6 weld-on rack, add the RUA12 crown.
• A flashing light: the ELDC flashing LED light or the WLT multifunction LED light. Mains-voltage lights such as the ELAC are not suitable.
• A 230 V AC, 50/60 Hz mains supply at the gate.
• Only if you want the gate to run during a power cut: the optional PS524 charge card with two B12-B batteries.
• The control unit also works with OXILR receivers, ERA INTI, ERA ONE / MYGO, MYGOBD and ERA ONE LR remotes, EPSB, EPMB and EPLB BlueBUS photocells, the EPMORB reflective and EPMOW wireless photocells, and F210B and FT210B BlueBUS safety devices.

Installation

A gate automation installer should fit it. The job involves fixing the 24.5 kg gearmotor on a base beside the gate, bringing the 230 V AC supply to it, fitting the rack along the gate leaf with the matching crown, setting the limit switch, wiring the BlueBUS photocells and the flashing light to the control unit, and programming the remotes into the OXIBD receiver.

Before you buy

• The rack is not included. The Run is supplied with a module 4 crown for the galvanised ROA7 or ROA8 rack; for the ROA81 module 6 weld-on rack, add the RUA12 crown. Order rack for the full length of the gate travel.
• No flashing light is supplied: add the ELDC or the WLT; mains-voltage lights such as the ELAC are not suitable.
• Battery backup uses the optional PS524 charge card with two B12-B batteries.
• Kit contents are as supplied and are confirmed when you order.